wall industries, inc. 5 watson brook road exeter , nh 03833 02/06/2013 603-778-2300 www.wallindustries.com fax 603-778-9797 page 1 of 4 datasheet rev. a psme 10 series 85~264vac (125~373vdc) input voltage range 10 watts, encapsulated pcb mount single outputs, isolation class ii medical ac/dc switching power supplies features isolation class ii fully isolated plastic case single outputs cooling by free air convection rohs compliant energy star compliant withstand 2g vibration test 10 watts output power universal input voltage: 85~264vac or 125~373vdc green design, no-load power consumption < 0.3w all using 105c long life electrolytic capacitors -20c ~ +70c wide operating temperature range 100% full load burn-in tested short circuit, over load, over voltage, and brown-o ut (low ac input voltage) protection ul60601-1, tuv en60601-1, and iec60601-1 medical ap provals description the PSME10 series of medical ac/dc switching power supplies provides 10 watts of continuous output pow er in a 2.76 x 1.97 x 0.89 encapsulated pcb mountable package. this series consists of 5v, 12v, 15v, and 24vdc ou tput mo dels with a universal input voltage range of 85~264vac o r 125~373vdc. these power supplies are protected against short circuit, over load, over voltage, and brown-out (lo w ac input voltage) conditions and have an mtbf of 210,2 00 hours using mil-hdbk-217f. this series also has ul60601-1 , tuv en60601-1, and iec60601-1 medical approvals. all models have been 100% full load burn-in tested and are rohs and energy star compliant. medical
rev. b PSME10 series single outputs, isolation class ii 10 watts, encapsulated pcb mount medical ac/dc switching power supplies wall industries, inc. 5 watson brook road exeter , nh 03833 02/06/2013 603-778-2300 www.wallindustries.com fax 603-778-9797 page 2 of 4 specifications: PSME10 series all specifications are based on 25c, nominal input voltage, and maximum output current unless otherwis e noted. we reserve the right to change specifications based on technological advances. specification test conditions min nom max unit input specifications ac input voltage range 85 264 vac input voltage range dc input voltage range 125 373 vdc input frequency 47 63 hz low line full load, vin = 115vac 0.25 input current high line full load, vin = 230vac 0.15 a low line cold start, vin = 115vac 25 inrush current high line cold start, vin = 230vac 45 a no load power consumption 0.3 w output specifications output voltage see table voltage tolerance -3 +5 % 5vdc output model -1 +1 load regulation 12v, 15v, & 24vdc output models 10% to 100% rated load -0.5 +0.5 % 5vdc output model -1 +1 line regulation 12v, 15v, & 24vdc output models low line to high line at rated load -0.5 +0.5 % output power 0 10 w output current see table ripple & noise (see note 1) see table low line full load, vin = 115vac 25 hold-up time high line full load, vin = 230vac 100 ms setup time (see note 3) full load, vin = 115/230vac 100 ms rise time full load, vin = 115/230vac 25 ms temperature coefficient 0~50c -0.03 +0.03 %/c protection over voltage protection latch-off mode 115 145 % over load protection hiccup mode, recovers automatically after fault con dition is removed 110 % short circuit yes brown-out (low ac input voltage) yes general specifications efficiency vin = 230vac see table withstand voltage (input to output) 4000 vac isolation resistance (input to output) 500vdc 100 m ? environmental specifications operating temperature with derating (see derating curve) -20 +70 c storage temperature -40 +85 c operating humidity non-condensing 20 90 % rh storage humidity 10 95 % rh vibration 10~500hz, 2g 10min/1cycle, period for 60 min each a long x, y, and z axes cooling free air convection mtbf mil-hdbk-217f 210,200 hours physical specifications weight approximately 3.7oz (105g) dimensions (l x w x h) 2.76 x 1.97 x 0.89 inches (70 x 50 x 22.7 mm) safety & emc safety approvals ul60601-1, tuv en60601-1, and iec60601-1 emi conduction & radiation en55011: 2007+a2: 2007 class b harmonic current en61000-3-2: 2006 class a, en61000-3-3: 1995+a1: 20 01+a2: 2005 ems immunity en60601-1-2: 2001+a1: 2006, iec61000-4-2,3,4,5,6,8, 11 light industry level, criteria a
rev. b PSME10 series single outputs, isolation class ii 10 watts, encapsulated pcb mount medical ac/dc switching power supplies wall industries, inc. 5 watson brook road exeter , nh 03833 02/06/2013 603-778-2300 www.wallindustries.com fax 603-778-9797 page 3 of 4 model selection table model number input voltage range output voltage output current ripple & noise (1) efficiency output power psme-10-05 5 vdc 2a 80mvp-p 77% 10w psme-10-12 12 vdc 0.83a 150mvp-p 79% 10w psme-10-15 15 vdc 0.66a 150mvp-p 80% 10w psme-10-24 85 ~ 264 vac or 125 ~ 373 vdc 24 vdc 0.42a 240mvp-p 82% 10w notes 1. ripple & noise is measured at 20mhz bandwidth b y using 12" twisted pair-wire terminated with 0.1f and 47f capacitors in parallel. 2. tolerance includes set up tolerance, line regul ation, and load regulation. 3. the length of the setup time is measured a firs t cold start. turning the power supply on and off v ery quickly may lead to an increase in the setup time. 4. the power supply is considered a component whic h will be installed into final equipment. the final equipment must be re-confirmed that it still meets emc directives. block diagram i/p emi filter rectifiers & filter power switching pwm control rectifiers & filter detection circuit +v -v derating curve 85 ta=25c 100 110 120 264 40 50 60 70 80 load (%) load vs input voltage input voltage (vac) 90 100 -20 ambient temperature (c) 0 10 20 30 40 50 60 70 20 40 60 80 100 load (%) load vs temperature
rev. b PSME10 series single outputs, isolation class ii 10 watts, encapsulated pcb mount medical ac/dc switching power supplies wall industries, inc. 5 watson brook road exeter , nh 03833 02/06/2013 603-778-2300 www.wallindustries.com fax 603-778-9797 page 4 of 4 mechanical drawing bottom view ac/n ac/l -v +v 0.295 (7.5) 0.315 (8) 2.13 (54) 2.76 (70) 1.97 (50) 0.689 (17.5) 0.789 (20.04) 0.59 (15) 0.138 (3.5) 0.041 (1.05) 0.89 (22.7) unit: inches (mm) company information wall industries, inc. has created custom and modified units f or over 50 years. our in-house research and development engineers will provide a solution that exceeds your performance requiremen ts on-time and on budget. our iso9001-2008 certification i s just one example of our commitment to producing a high quality, well-documented product for our customers. our past projects demonstrate our commitment to you, our cus tomer. wall industries, inc. has a reputation for working cl osely with its customers to ensure each solution meets or exceeds form, fit and function requirements. we will continue to provide ongo ing support for your project above and beyond the design and pro duction phases. give us a call today to discuss your future projects. contact wall industries for further information: phone : (603)778-2300 toll free : (888)597-9255 fax : (603)778-9797 e-mail : sales@wallindustries.com web : www.wallindustries.com address : 5 watson brook rd. exeter, nh 03833
|
